Sisneros Bros. Manufacturing, Belen, New Mexico, USA
Battery manufacturingStainless process duct

Fullypenetrated& fullycertified.

In a cell plant, the duct is part of the process. Sisneros Brothers builds precision-fabricated stainless steel duct with full-penetration welds to AWS B2.1 and AWS D9.1, by AWS B2.1-certified welders, for battery manufacturers and the mechanical contractors who build their plants.

The Sisneros Difference

  • WELDFull penetration to AWS B2.1, adheres to AWS D9.1
  • WELDERSEvery welder AWS B2.1 certified
  • MATERIALASTM A240 Type 304/304L, 316 on request
  • RANGE3″ to 48″ Ø round, plus custom fittings
  • SUPPORTEstimating and take-off by Industrial Ducting Systems
Companies with facilities using our ducting
BoeingSpaceXLGGoogleFordLockheed MartinTeslaIntel
Fully Penetrated Welds

The seam decides how long the system lasts.

A weak seam leaks solvent and corrodes first. That’s where most fabricators fall short, and where Sisneros fully penetrated welds are the strongest.

  1. The stakes

    Duct is part of the process.

    A weak seam leaks solvent and corrodes first.

  2. The gap

    Seamed and sealed isn’t fully welded.

    Duct is seamed and sealed, not fully penetration-welded to AWS code.

  3. The answer

    Welded to AWS B2.1 and D9.1.

    Full-penetration welds by certified welders, on every seam.

  4. The result

    Duct that outlasts the chemistry.

    Protects yield, keeps the dry room dry, and holds up to the process.

Sisneros Bros. Manufacturing
Certified welds that protect the cell, the process and the plant.
Fully welded stainless steel LF Ducting pipe and fittings
LF Ducting: fully welded 304 stainless pipe and fittings
Chemistries

What your duct is up against.

Battery manufacturing carries three families of chemistry. Here is what each one attacks and how stainless and a full-penetration weld address it.

Acid gases and condensate

HF (from LiPF6 and moisture), acid mist, NOx where thermal oxidizers run

What it attacks
Carbon steel, galvanized and glass. Stainless too, once condensate forms.
How the material answers
304/304L in dry service. 316L where condensate is likely. Confirm against your chemistry.
How the weld answers
Continuous full-penetration welds leave no laps or crevices to hold condensate, and a leak-tight run keeps humid air out.

Process solvents

NMP, carbonate solvents, isopropyl alcohol, acetone

What it attacks
Plastics, elastomers, sealants and adhesives. Not stainless.
How the material answers
Stainless isn’t the weak point, so the metal choice is simple.
How the weld answers
No sealant in any seam for solvent to soften. Joint gaskets selected for the solvent and temperature.

Alkaline dust and mist

Lithium hydroxide, lithium carbonate, caustic scrubber carryover

What it attacks
Aluminum and zinc coatings.
How the material answers
Stainless has no coating to strip.
How the weld answers
A smooth welded interior with no seam pockets for dust to pack into.

The material resists the chemistry. The weld seals the system. Your testing lab confirms the fit.

Chemistry varies by manufacturer, so confirm material, gasket and sealant selection against your own process. Ask for the full chemical list, with CAS numbers for your testing lab.

Our value

Four reasons you want us.

Sisneros’s value comes from a history of delivering quality stainless steel ducting for challenging process systems and delivering it fast enough to meet critical timelines.

Sealed by the weld

Full-penetration welds performed by AWS B2.1-certified welders.

Holds dew point and keeps solvent in the loop.

Built to the code

High-quality welds that meet AWS B2.1 and AWS D9.1.

A weld standard owners can write into the spec.

Trusted & approved

Trusted in semiconductor, cleanroom, chemical processing and high-performance exhaust.

The standard critical systems already demand.

Built at speed

Custom fabrication for each process and each piece of equipment, on scheduled production timelines.

New construction, retools and expansions start up on schedule.
Your needs

Built for the people who spec it, buy it and sign off on it.

Pick your seat on the project and see the value we deliver.

What you want

Stainless that arrives built to drawing and fits up clean in the field.

What we deliver
  • Estimating, take-off and project coordination through Industrial Ducting Systems
  • Round parts formed on a CNC 4-roll bender with pre-bend, so joints line up
  • Standard 59″ and 60″ pipe sections, with elbows at 1.5 × D and 2″ tangents
  • Built and shipped to your install schedule
Request Sales Estimate
Specification language

Write the weld into the spec.

A starting point for owner facilities engineers and engineers of record. Copy it into your Division 23 section, then edit it for your project.

  • ConstructionFormed on a CNC 4-roll bender with pre-bend for true roundness
  • WeldingContinuous fusion butt weld, back-purged, per documented WPS #SBM-301
  • FinishStandard #2B, passivated per AMS 2700. Electro-polish and #4 available.
  • JointsLF Clamp (3″–18″) and LF Bolt / Vanstone flange (20″–48″)
23 35 00 · process exhaust duct (suggested)

A. Material. Process exhaust duct serving battery cell production areas shall be ASTM A240 Type 304/304L austenitic stainless steel, cold rolled, annealed and pickled. Material gauge shall be selected by the manufacturer for the duct diameter, system pressure and application.

B. Seams. All seams shall be continuous full-penetration butt welds. Seamed, snap-lock or sealant-dependent construction is not acceptable.

C. Weld quality. Welds shall meet AWS B2.1 and AWS D9.1, performed to a documented weld procedure specification by welders certified to AWS B2.1. Welds shall be back-purged.

D. Finish. #2B finish, passivated per AMS 2700.

E. Joints. Flanged or clamped connections with gaskets selected for the temperature and chemistry conveyed.

F. Basis of design. Sisneros Bros. Mfg. LF Ducting, or approved equal.

Products

Leak-free. Fully welded. 3″ to 144″.

Standard 304 and 316 stainless steel pipe, fittings, airflow control, and flanges, built for corrosive fumes, abrasion, and heat. When the equipment calls for something that isn’t in the catalog, we build that too.

Seam-welded pipe, 5′ section, 304 stainless with flange connection

Seam-welded pipe, 5′ section

3″–48″ Ø · 304 SS
## LPLF
90° elbow, 304 stainless with flange connection

90° elbow

3″–48″ Ø · 304 SS
E##90FL
60° elbow, 304 stainless with flange connection

60° elbow

3″–48″ Ø · 304 SS
E##60FL
45° elbow, 304 stainless with flange connection

45° elbow

3″–48″ Ø · 304 SS
E##45FL
30° elbow, 304 stainless with flange connection

30° elbow

3″–48″ Ø · 304 SS
E##30FL
45° branch, 304 stainless with flange connection

45° branch

3″–48″ Ø · 304 SS
B45FL##,b,c
30° branch, 304 stainless with flange connection

30° branch

3″–48″ Ø · 304 SS
B30FL##,b,c
90° tee branch, 304 stainless with flange connection

90° tee branch

3″–48″ Ø · 304 SS
TBFL##,b,c
60° wye branch, 304 stainless with flange connection

60° wye branch

3″–48″ Ø · 304 SS
YBFL##,b,c
Concentric reducer, 304 stainless with flange connection

Concentric reducer

3″–48″ Ø · 304 SS
RFL##,b
Square to round, 304 stainless with flange connection

Square to round

3″–48″ Ø · 304 SS
SQRFL##,axbl
Blast gate, manual (automatic 36″+), 304 stainless with flange connection

Blast gate, manual (automatic 36″+)

3″–48″ Ø · 304 SS
BGFL##
Volume control damper, 304 stainless with flange connection

Volume control damper

3″–48″ Ø · 304 SS
VD##
Blind flange (end cap), 304 stainless with flange connection

Blind flange (end cap)

3″–48″ Ø · 304 SS
BF##

Dimensions

Elbows at 1.5 × D centerline radius with 2″ tangents both ends. Pipe in 59″ (bolt) or 60″ (clamp) sections. Diameter is clear inside diameter.

Custom work

Round, oval and rectangular. 304 and 316 stainless, 10 ga to 28 ga. TIG, MIG and plasma full weld. Electro-polish, #4 and brushed finishes.

Connections

LF Clamp, LF VS flange, flat-lip and curled-edge clamp, slip fit, bell and spigot, butt weld. Matched to an OEM’s connection spec on request.

Welded stainless process duct installed across the ceiling of a large manufacturing plant
Stainless duct connected to a dust collector
Custom rectangular stainless duct on the shop floor
Parallel runs of welded stainless process duct suspended from a plant ceiling
Trusted & approved

Proven where failure isn’t an option.

In addition to battery, our duct is already running in the plants that allow the least margin for error.

Battery manufacturingLG Energy Solutions, Ford: Blue Oval
SemiconductorWorld’s largest semiconductor manufacturer, Philips, Motorola
National labsLos Alamos, Sandia Labs, NASA
Pharma and chemicalBristol-Myers Squibb, Ethicon, Sud-Chemie
Aerospace and defenseBoeing, Dept. of the Navy, White Sands
Heavy industryU.S. Steel, General Electric, Phelps Dodge

Family-owned since 1985. Three generations of the Sisneros family have been building ductwork in Belen, New Mexico, and shipping nationwide.

Start a project

We got your back.

Tell us about the project, and get support with estimating, take-off, and a delivery schedule built around your installation plan.

Industrial Ducting Systems

Sold and supported by Industrial Ducting Systems

Sisneros Brothers’ preferred partner for estimating, take-off and project coordination.

Visit Industrial Ducting Systems

Contact us directly
(877) 273-0291 · sales@batteryduct.com

Your request goes to the Sisneros and Industrial Ducting Systems team.